1911 Forums : 1911Talk banner
Status
Not open for further replies.
1 - 20 of 25 Posts

·
Banned
Joined
·
1,461 Posts
Discussion Starter · #1 ·
I will be installing them on Friday including a Med. Greider trigger and Hammer struts and pins. Also will be the hammer and sear and sear spring and disconector.
It should give me a 3.5 trigger pull. I brought the Ultra match kit 8)
S/F Vic
 

·
Premium Member
Joined
·
5,072 Posts
Very sweet. I like greider triggers and c&s parts a lot. It sould be a great shooter.
 

·
Banned
Joined
·
1,461 Posts
Discussion Starter · #3 ·


These parts go in tomorrow a Greider Match trigger, which is O/S to fit in to avoid any vertical play. C&S Hammer, and Sear matched and a C&S Hammer Strut and new pins and Disconnecter. The springs I always have extra's in house. I also installed the EGW firing pin stop which doesn't do much on external extractors but I hate the sloppy fits that come with most pistols so i make them a slip fit.
 

·
Banned
Joined
·
1,461 Posts
Discussion Starter · #4 ·
Well I finished lol a bit early

I also made my SIG TTT now a Series 70 Model also he he.
I also found I had a TJ's shim which takes the place of the 4 parts to make it a series 80. The plunger and spring on the slide are removed, plus on the frame the two shim parts that block the firing pin. I got the trigger down to 3.18 LBS. I will not carry it but will use it in matches.
The Slide missing the Plunger and spring

The slide missing the two shim parts


The finish product: The Greider trigger would not reset the grip safety so I changed it.
 

·
Premium Member
Joined
·
5,072 Posts
I put the TJ's shim in any 80's series 1911, that should be one outstanding sig with those c&S parts.
 

·
Registered
Joined
·
4,029 Posts
Good parts C&S is good stuff about the only true drop in parts out there
 

·
Registered
Joined
·
4,029 Posts
Ive only used one set from them but yeah they are good parts i want to try the Warp speed set up in my Colt Comp Gun
 

·
Registered
Joined
·
4,029 Posts
3.5 with that wild hammer

 

·
Banned
Joined
·
1,461 Posts
Discussion Starter · #12 ·
Yep that is it, I received my kit within 5 days. Polish the ends of the sear spring and a little bending you can make it less even.
 

·
Registered
Joined
·
4,029 Posts
Yep that is it, I received my kit within 5 days. Polish the ends of the sear spring and a little bending you can make it less even.
Yes i tweaked my other kit down to little under 4# for the 22 Conversion kit gun i built up .. its Amazing what a little polishing can do..
 

·
Registered
Joined
·
4,029 Posts
I still do it all by hand with Flitz i need a buffer wheel
 

·
Registered
Joined
·
4,029 Posts
Im thinking on it i got a slide i want to repolish after bead blasting ...
 

·
Registered
Joined
·
4,029 Posts
Ahh ill get one eventually the slide didnt come out the way i wanted i wanted a hard matte finish
 

·
Banned
Joined
·
1,461 Posts
Discussion Starter · #20 ·
You are easy to talk into buying one , but once you get one you will find a million uses for it. I even highly Polished my Ruger Mark 111, insided and out.
 
1 - 20 of 25 Posts
Status
Not open for further replies.
Top